« previous next »
Pages: [1]   Go Down

Author Topic: Making a new fire pot  (Read 3122 times)

0 Members and 1 Guest are viewing this topic.

Offline Brodie Tas

  • Tent User
  • ***
  • Posts: 243
  • Thanked: 19 times
  • Gender: Male
Making a new fire pot
« on: October 10, 2017, 07:16:08 PM »
Hi so I just picked up I just picked up a small hot water cylinder going to start cutting it up next weekend because I'm heading away this weekend, its going to be a similar set up as the picture below but I'm thinking of cutting some of the top flat so I can put a removable BBQ plate on it to make cleaning it easier. Also going to put a bent flute on it so I can sit it under my gazebo a bit, also trying to think of a way to be able to brake the flute down in 3 or 4 bits easier for transport anyone got a way? Post a pic of yours to give me some ideas

« Last Edit: October 10, 2017, 07:46:52 PM by Brodie Tas »
Logged

Offline speewa158

  • Hard Top Camper User
  • ******
  • Posts: 12092
  • Thanked: 558 times
  • Gender: Male
Re: Making a new fire pot
« Reply #1 on: October 10, 2017, 07:23:02 PM »
Have a look it the blank  & think about just where you want it to be after its cut up .   Play with the design on paper then , Rip into it .
lf it all turns sH1T  trash it a go again . You wont be the 1st to do so  .
                                        Enjoy       :cheers:
Logged
You can go your own way . Treg Up & Make Dust

Offline Brodie Tas

  • Tent User
  • ***
  • Posts: 243
  • Thanked: 19 times
  • Gender: Male
Re: Making a new fire pot
« Reply #2 on: October 10, 2017, 07:47:44 PM »
Yeah that's it I will have a play around
Logged

Offline speewa158

  • Hard Top Camper User
  • ******
  • Posts: 12092
  • Thanked: 558 times
  • Gender: Male
Re: Making a new fire pot
« Reply #3 on: October 10, 2017, 08:18:48 PM »
That looks like a 9KG bottle to me . Dime a dozen to acquire . 
Degas them then cut them up to a unit that suites your purpose  & go from there  . The flue can be rectangular  Gal down pipe cut & teck screwed to make the bends . Just how flash do you need to be     ???
lf it all turns to Sh1t start again with another plan  ,  whats it cost you    ,  ???
4/5 of 5/8 of SFA  &  :cheers:
                                       ;D ;D ;D              :cheers:         :cup:
Logged
You can go your own way . Treg Up & Make Dust

Offline Brodie Tas

  • Tent User
  • ***
  • Posts: 243
  • Thanked: 19 times
  • Gender: Male
Re: Making a new fire pot
« Reply #4 on: October 10, 2017, 08:37:38 PM »
Yeah that's a gas bottle but that's just a idea my hot water cylinder will be a bit bigger and I didn't think about a down pipe I'll head up to the tip shop and see what I can find
Logged

Offline speewa158

  • Hard Top Camper User
  • ******
  • Posts: 12092
  • Thanked: 558 times
  • Gender: Male
Re: Making a new fire pot
« Reply #5 on: October 24, 2017, 07:05:23 PM »
Now your thinking    :cup:
l teck screwed to rectangular down pipes together  , cuttng out the lower 200mm internal walls to place the flue This is  over a recycled wet sleeve from a Massy tractor welded to the hole cut in the gas can end . That gives you a solid base to work from .
Experiment , work plans , rework plans  Enjoy     :cheers:
Try the bins of construction sites for bits     :cheers:
Logged
You can go your own way . Treg Up & Make Dust

Offline Bird

  • Once Was Lost, now am found
  • Hard Top Camper User
  • ******
  • Posts: I am a geek!!
  • Thanked: 1874 times
  • Gender: Male
  • Life is far too long....
    • My Place.
Re: Making a new fire pot
« Reply #6 on: October 25, 2017, 07:22:57 AM »
Logged
-
Click to enlarge

Gone to a new home
Pages: [1]   Go Up
« previous next »