MySwag.org The Off-road Camper Trailer Forum
General => General Discussion => Topic started by: Paul Mac on May 05, 2011, 09:58:31 PM
-
Hi folks,
I drive an NS Pajero and live in the outer south eastern suburbs of Melbourne.
Looking for some local knowledge please.
I'm looking to install a 2 drawer and fridge slide into my vehicle and was wanting to find out where to go or where to look for pricing. As I'm a poor ol retiree price is somewhat of an issue. I've already looked at the Black Widow drawer system and at $2,050 without the fridge slide I think that is a tad expensive.
Can anyone provide some recommendations on where to go thanks.
Cheers
Macca
-
There's a dude on the Patrol forum who makes them, can't think of his name off the top of my head.
Have you looked at the Drifta drawers?
-
Thanks D4D,
Are you thinking of Jimmy Best ?
I should also mention that I'm looking for the drawer system to be made from metal rather than timber too.
I believe Jim constructs his drawers with timber.
Thanks again.
-
these guys make a nice setup..
http://www.offroadsystems.com.au/
-
Macca what about Fourby fitouts in Hallam, not sure of there prices but could be worth a look.
http://www.fourbyfitouts.com.au
I have no affiliation with them but I did have a good look at there gear at Wandin 4WD Day.
Rich
-
I can highly recommend Trek Tech: http://www.trektech.com.au/
Although based in Adelaide they will freight and it probably would still work out cheaper!
For my Pajero he did my storage shelf, cargo barrier, tilting fridge slide, and I am about to get a fridge cage made up by him -couldn't be happier!
-
these guys make a nice setup..
http://www.offroadsystems.com.au/
I think they have a DIY section as well know where you can buy all the parts and mecanno set it
GG
-
Thanks heaps for the info so far guys.
I will pop down to see the Hallam factory today and take a look at their systems.
Cheers
Macca
-
Can't go past Jim Best ( Best Offroad ) for price and service ...
Wish I had room for them ... ???
:cheers: :cheers: :cup: :cheers: :cheers:
-
Yeah Steve, I've met Jimmy a few times and had a look at his operations and I will also give his place a visit to see if he will do metal systems
Thanks also for the response.
Cheers
-
I have a set of Tanami drawers in the Patrol, they are aluminium and super strong, the factory is in Frankston if I remember rightly
GG
-
Have you thought of making your own? You can use Kubelock (but dont use the plastic joins)
EG: http://forums.overlander.com.au/viewtopic.php?t=30055&highlight=storage
-
Hey Lost,
Do you happen to know where you can get the metal connectors? I've recently grabbed some the Qubelok stuff that Bunnings sell (at ridiculously inflated prices), and while the plastic connectors will be fine for what I'm using it for I'd like to grab some of the metal ones for a drawer system. The other option though, which I must admit I'm coming back towards, is just to weld up a steel frame. It'll be heavier than the alloy, but much easier and hopefully stronger.
Re: OffroadSystems - I've not bought anything from them, but when I last talked to them about drawers, water tanks and cargo barriers, they couldn't help me enough. I felt bad not going ahead with things at the time, simply because their service was so outstanding.
GG's Tanami drawers look pretty cool too!
Thanks!
Matto :)
-
Hi Matto,
The storage system, below, came out of a need to reduce the weight of my previous wooden box/draw setup.
Got this made to hold 4 boxes on top, 6 in the middle, and 2 long and 2 short on the bottom..
It is made in 3 parts..The fridge and lower level, the middle and top level, and the water tank/ cargo barrier behind. These all bolt to floor and each other.
I have put a couple of boxes in to show them loaded.
They are very basic and very light. The cargo barrier is part of the 75L tank. This setup is very strong, gone nearly everywhere..
-
these guys make a nice setup..
http://www.offroadsystems.com.au/
Yep got them in my PJ originally in the Pathie then modded for the PJ at far less cost than a new system, mine is Aluminium/timber,
this year they went to the Melbourne Show, best part is they'll custom build within reason
-
Hey Lost,
Do you happen to know where you can get the metal connectors? I've recently grabbed some the Qubelok stuff that Bunnings sell (at ridiculously inflated prices), and while the plastic connectors will be fine for what I'm using it for I'd like to grab some of the metal ones for a drawer system. The other option though, which I must admit I'm coming back towards, is just to weld up a steel frame. It'll be heavier than the alloy, but much easier and hopefully stronger.
Try here -> http://www.capral.com.au/
-
Try here -> http://www.capral.com.au/
I asked the bloke at capral if they did the collectors in Al, and he claimed that they didnt ???
-
I asked the bloke at capral if they did the collectors in Al, and he claimed that they didnt ???
in that case, no idea... they did yrs back when this stuff first showed its head and Dave made his unit. :(